R110i-1 Getting Started

* The preview only show first 10 pages of manuals. Please download to view the full documents.

Loading preview... Please wait.

Manuals information


Report / DMCA this file

Manuals Content

Express5800/R110i-1

Getting Started!

Step 1 ●

Getting Started (this guide) × 1



Safety Precautions and Regulatory Notices × 1



SDR Update CD-ROM × 1



Power cord × 1 or × 2*



Front Bezel × 1

Be sure to read this guide carefully before using this



Cable ties (for securing AC power cord) × 1 or × 2*

server and keep this guide for future use.



The tool used for removing slide rails (outer rails) × 1

Read and follow Safety Precautions and Regulatory Notices that comes with this product first.

The following describes the procedures from opening the carton box to starting using this product. Be sure to follow these steps.

Instruction Manuals Instruction manuals are available at NEC Web Site (http://www.nec.com/). To see the manuals in EXPRESSBUILDER, follow the steps below. (1) If you already have the EXPRESSBUILDER DVD, set the DVD into a computer running Windows. Follow the on-screen messages to start the menu, and then go to (4).

Connect cables

Connect cables to the server.

Express5800/R110i-1 server × 1



First Edition, Apr 2017

Step 4

Check the accessories

Open the carton box, and then make sure you have all the accessories listed below:

Note: For details on how to install the server in the rack, see “Installation and Connection” in User’s Guide. USB device

USB device

Important: Keep accessories for future use. * EXP335A only

Step 2

Install internal optional devices

Install internal optional devices. Go to Step 3 if you have not purchased optional devices or if you purchased a Build to Order (BTO) product.

Front

Note: See “Installing Internal Optional Devices” in User’s Guide and the manual that comes with the optional device.

Tips: You can download EXPRESSBUILDER from NEC Web Site. (2) To install Windows, follow this guide (reverse side). (3) After installing Windows, click NEC EXPRESSBUILDER on the desktop or Start Menu.

Step 3

(4) Click Instruction Manuals on the following menu.

Install the server into a rack under the following conditions.

Place the product to a proper location

Note: For details on how to install the server in the rack, see “Installation and Connection” in User’s Guide.

Device with the serial interface

Hub, switching hub, ...

Finally, connect the 1 power cord to an outlet.* For connecting to the UPS, refer to the next section. Ports for data transmission 1000BASE-T 100BASE-TX 10BASE-T

Do not use the server in an environment where corrosive gas is present. Environment: Ambient temperature:5°C to 40°C* Humidity: 10% to 85% Temperature gradient: ±10°C/hour Air pressure: 749 to 1040 hpa Ambient temperature: 5°C to 40°C* Humidity: 10% to 85% Temperature gradient: ±15°C/hour Air pressure: 749 to 1040 hpa±15°C/hour Air pressure: 749 to 1040 hpa

Leave the minimum clearance around the rack: 1 m to the front/rear, 60 cm to the sides, and 40 cm above the top

Rear When using multiple racks, be sure to join them

*: 5°C to 45°C (when an optional kit is installed; subject to composition restrictions)

Outlet or UPS is within reach of the attached power cord

Management LAN connector 1000BASE-T 100BASE-TX 10BASE-T

Attach stabilizers

100/200VAC bipolar grounded outlet or bipolar outlet with ground terminal or UPS

USB device

USB device

Display unit

Hub, switching hub, ...

Flat and solid floor

*1 Connect the power cord to a circuit breaker of up to 15A. To prevent power cord from disconnecting, secure the power cord with the provided cable tie.

Step 5

To install bundled software, follow the steps below.

(9) Choose Setup from Home Menu.

Turn on the server, and then set up the OS

Follow the steps below to set up the server. (1) Remove peripherals except display, keyboard and mouse, and then turn on a display. (2) If STATUS LED 1 lights green and STATUS LED 2 lights amber, wait until these LEDs are turned off. (3) Press POWER Switch. NEC logo will appear on the screen.

(10) To choose installed OS, click a button on the menu of step 1, and then click the right arrow icon to proceed. (11) To specify settings, click a button on the menu of step 2, and then click the right arrow icon to proceed. (12) After confirming the settings, click the right arrow icon of step 3, and then click Start of step 4. (13) To proceed with setup, follow the on-screen message. In the automatic installation, do not operate the keyboard and mouse until the OS license screen appears.

Important: If an error message appears on the screen or beeps are heard repeatedly after turning on the server, write down the displayed message or the beeps pattern, and then contact your sales representative.

(14) After the OS installation, configure the OS and drivers, if necessary. For details, see Installation Guide (Windows).

Tips: For details about bundled software, see the manuals by clicking “Instruction Manuals” in step 3 below. (1) When installing bundled software into the server, start Windows installed in the server. When installing bundled software into “PC for Management”, start Windows installed in the PC. (2) Log on to Windows as an administrator. (3) When installing into the server, click NEC EXPRESSBUILDER on the desktop. When installing into “PC for Management”, download EXPRESSBUILDER and set it to the PC. The following menu will appear.

Tips: To see the guide, click NEC EXPRESSBUILDER on the desktop or go to NEC Web Site.

(4) Press key while the following message appears on the bottom of screen. (The message depends on hardware configuration) Press SETUP, Internal Flash Memory, ROM Utility, Network BIOS Setup Utility will start after a while.

Windows Service Pack When applying Windows Service Pack to this server, see “Supported Service Pack” in Installation Guide (Windows).

(5) Change the following BIOS settings depending on the OS. *1

Windows Server 2016 Windows Server 2012 R2 Windows Server 2012 Windows Server 2008 R2

X2APIC Enabled Enabled Enabled Disabled

*2

Boot Mode UEFI UEFI UEFI Legacy

*1 Choose Advanced menu, and then choose Processor Configuration.

Step 6

Install the bundled software

The following software is bundled with this server. Install the software as needed. Tips: “PC for Management” can assign a general Windows computer. You can also use this server as “PC for Management”.

*2 Choose Boot menu.

Press key to save the changes. The server restarts automatically after the utility is terminated. (6) Press key while the following message appears on the bottom of screen. Press SETUP, Internal Flash Memory, ROM Utility, Network Tips: You can run EXPRESSBUILDER when inserting EXPRESSBUILDER DVD into the server instead of pressing key. EXPRESSBUILDER will start after a while.

(7) Choose OS installation from Boot Selection Menu.

Name

Where to Install

(4) Click Integrated Installation or Applications on the menu. (5) Select bundled software to install.

Description

NEC ESMPRO ServerAgentService

Server

Monitors the server status.

NEC ESMPRO Agent Extension

Server

Remotely controls the server.

Express Report Service

Server

Informs the support center of the failure information.

Express Report Service (HTTPS)

Server

Informs the support center of the failure information.

NEC ExpressUpdate Agent

Server

Manages and updates the versions of firmware, software, and other products installed in the server.

Universal RAID Utility(URU)

Server

Manages and monitors the RAID controller.

Product Info Collection Utility

Server

Collects information for maintenance.

Ezclct Viewer

Server

Display the log files collected by Product Info Collection Utility.

Server Configuration Utility

Server

Sets up BMC.

NEC ESMPRO Manager

PC for Manages the server by integrating with Management NEC ESMPRO ServerAgentService or other products.

Express Report Service (MG)

PC for Informs the support center of the Management failure information.

(8) Choose your language and agree the end user license. The following menu will appear.

Tips: You can copy bundled software to removable media by clicking Maintenance and can install the software into the PC with the media.

(6) Follow the on-screen message to proceed. For details, see Installation Guide and other manuals.

Trademarks Microsoft, Windows and Windows Server are registered trademarks or trademarks of Microsoft Corporation in the United States and other countries. All other product, brand, or trade names used in this publication are the trademarks or registered trademarks of their respective trademark owners. This guide uses recycled paper. © NEC Corporation 2017 This document may not be copied or altered without the permission of NEC Corporation.

Similar documents